|
Products
Adapter board
Lighting
Coloured wire
|
54670 Power Pack
The
ESU Power Pack can be optionally connected to all LokPilot V4.0,
LokPilot micro V4.0, LokSound V4.0, LokSound micro V4.0 and LokSound
V4.0 M4 decoders and supplies your locomotive reliably with power to
get over dirty tracks and longer switch crossings.
Sound, light and motor functions are buffered and thus enable your
model to run up to 3 seconds without power, depending on the models
power consumption.
The
Power Pack has an integrated charging current which is controlled by
the decoder. Therefore it can remain within the loco while it gets
programmed. The load current is however, limited to avoid an
excessive load on your booster, for this case there would be,
several models in operation.
The
buffer time can be restricted by writing a CV on the decoder side to
make red signals lead to an exact signal stop.
The
size of the Power Pack is approx. 22 x 10 x 14 mm which has to be
considered during the installation.
A 3-pin cable
connection between the decoder and the Power Pack is essential.
Please
note that the PowerPack is automatically disabled during
conventional AC/DC operation. For technical reasons, buffering is
not possible.
Top of page
51967 Adapter board
The 21 MTC adapter board
is suitable for digitising a loco without an interface.
The adapter board offers
a possibility for installing a decoder with 21MTC connector.
This decoder is simply plugged onto the board. At the other
end 21 annular rings make wiring of your loco possible.
A neat conversion can be made via this adapter board and enables you
to use all additional functions of the 21MTC connector (e.g. loud
speaker outputs).
51968 Adapter board 2, with Aux 3 / 4
The 21 MTC adapter board
2 is also suitable for digitising a loco without interface. It is
very helpful, if you do not intend to wire the decoder freely or if
you wish to use more than four function outputs on your LokPilot or
LokSound decoder.
Decoders with 21MTC
connectors (ESU LokPilot or LokSound favoured) are simply plugged
onto the adapter board.
On the output side, the
adapter offers pre soldered cables (appr. 20cm length). There are
amplifiers (appr. 250mA each) for functions AUX3 and AUX4 (the
decoder´s logical outputs) so that ESU decoders can now have up to 6
function outputs, two for lights and four Auxiliary.
Top of page
Lighting
ESU
is very proud to present to you the new interior LED
lighting system for passenger cabins. This system
allows you to retrofit your cars with a prototypical
and steady interior lighting. The passenger car
interior lighting is available in three different
versions to match the desired location.
For the
gauges N, TT and H0 imaginary, 255mm long lightings
will be offered in two versions: With warm white
LEDs (50700) or yellow LEDs (50702).
The long
car interior lighting with the SKU 50703 is designed
for use in G gauge cars (e.g. for the three axle "Umbauwagen"
of Märklin®). It features both white and yellow LEDs,
which can be adjusted separately in brightness. For
the first time you can adjust to the desired hue by
yourself. Because of the digital interface (21MTC) a
LokPilot Fx function decoder can be simply
retrofitted at any time.
Small,
easy to install kits for cabs and taillights are
also available.
The ESU
passenger car lighting system offers crucial advantages:
Warm-White LEDs
SMD LEDs, the
latest design, insure a uniform illumination of the cars at
extremely low power consumption.
Constant voltage
Thanks to
built-in voltage control the brightness remains almost
constant even when conventional driving.
Adjustable
brightness
With the help of
a small variable resistor (potentiometers) you can
individually adjust the brightness according to your wishes.
Variable length
The lighting
strips can be arbitrarily cut to fit the cars of all
manufacturers.
Buffer capacitor
The 255mm long
luminaries include a buffer capacitor to bridge small power
interruptions.
PowerPack
To bridge
prolonged power interruptions, the 255mm long lighting strip
can be retrofitted with an optional „Power Pack“. This
capacitor with extremely high capacity is standard at the
380mm illumination.
Taillights
included
Each lighting
strip comes with a red taillight. When not in use, this
lighting strip can be easily removed.
|
|
Art.No. |
Description |
|
50700
|
LED
lighting strip with taillight, 255mm, 11 LEDs,
warm-white. For gauge N, OO, O |
|
|
50703
|
LED
lighting strip with taillight, 380mm, 32 LEDs,
white/yellow, For gauge 1,G |
|
|
50704
|
LED
lighting strip, cabin, 1 LED, warm-white |
|
|
50705
|
LED
lighting strip, taillight, 2 LED, Red |
|
Top of page
51940 - 51949 Coloured Wire
|
If you work on locos and decoders (e.g. run
wires from loco to tender), you need thin, extremely
flexible cables. These are not always easy to get.
Responding to many requests from our customers, as of now we
offer you super thin cables (AWG 36) with an outside
diameter of only 0.5 mm (0.02 inch), in all common DCC
colours. They come in 10 m (30 feet) bundles at an affordable
price.
51950 8 pin Harness
NEM 652
51951 6 pin Harness
NEM 651
If the loco in
question features no digital interface and you don’t want to
cut off the interface-plug of your loco, simply make use of
one of our harnesses 51950 resp. 51951: Solder in the
harness and then plug in the decoder. That’s how the Pro’s
do it!
Ordering Information
|
|
Item
No. |
Description |
|
|
51940
|
Super
thin cable, 0.5mm diameter, AWG36, 10m bundle, white
colour |
|
|
51941
|
Super
thin cable, 0.5mm diameter, AWG36, 10m bundle,
purple colour |
|
|
51942
|
Super
thin cable, 0.5mm diameter, AWG36, 10m bundle, black
colour |
|
|
51943
|
Super
thin cable, 0.5mm diameter, AWG36, 10m bundle, red
colour |
|
|
51944
|
Super
thin cable, 0.5mm diameter, AWG36, 10m bundle,
orange colour |
|
|
51945
|
Super
thin cable, 0.5mm diameter, AWG36, 10m bundle, green
colour |
|
|
51946
|
Super
thin cable, 0.5mm diameter, AWG36, 10m bundle, grey
colour |
|
|
51947
|
Super
thin cable, 0.5mm diameter, AWG36, 10m bundle,
yellow colour |
|
|
51948
|
Super
thin cable, 0.5mm diameter, AWG36, 10m bundle, brown
colour |
|
|
51949
|
Super
thin cable, 0.5mm diameter, AWG36, 10m bundle, blue
colour |
|
|
51950
|
cable
harness with 8-pin plug NEM 652, DCC colour, length
300mm |
|
|
51951
|
cable
harness with 6-pin plug NEM 651, DCC colour, length
300mm |
|
Top of page
|
